Sprawdź zebrane popularne normy i standardy EMC i bezpieczeństwa, podzielone według branży.

Spis treści

  1. Wymagania urządzeń komercyjnych, powszechnego użytku
  2. Wymagania samochodowe, automotive
  3. Wymagania medyczne
  4. Wymagania Wojskowe – militarne, obronne
  5. Wymagania lotnicze, awionika, samolotowe
  6. Popularne wymagania bezprzewodowe

Zobacz takze listy norm zharmoniowanych z dyrektywami – wpis -WYMAGANIA DLA ELEKTRONIKI, KTÓRE NALEŻY WZIĄĆ POD UWAGĘ PRZY OCENIE ZGODNOŚCI 

Lista norm wg branży – EMC for Business v01_2018 – pobierz plik PDF (download PDF)

1. Wymagania urządzeń komercyjnych, powszechnego użytku

COMMERCIAL STANDARDS

ANSI  (http://webstore.ansi.org)

Document Number Title
C63.4 Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz

IEC (https://webstore.iec.ch)

Document Number Title
IEC 61000-3-2 Electromagnetic compatibility (EMC) – Part 3-2: Limits – Limits for harmonic current emissions (equipment input current ≤ 16 A per phase)
IEC 61000-3-3 Electromagnetic compatibility (EMC) – Part 3-3: Limits – Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current ≤ 16 A per phase and not subject to conditional connection
IEC 61000-4-2 Electromagnetic compatibility (EMC)- Part 4-2: Testing and measurement techniques -Electrostatic discharge immunity test
IEC 61000-4-3 Electromagnetic compatibility (EMC) – Part 4-3 : Testing and measurement techniques -Radiated, radio-frequency, electromagnetic field immunity test
IEC 61000-4-4 Electromagnetic compatibility (EMC) – Part 4-4 : Testing and measurement techniques –Electrical fast transient/burst immunity test
IEC 61000-4-5 Electromagnetic compatibility (EMC) – Part 4-5: Testing and measurement techniques -Surge immunity test
IEC 61000-4-6 Electromagnetic compatibility (EMC) – Part 4-6: Testing and measurement techniques -Immunity to conducted disturbances, induced by radio-frequency fields
IEC 61000-4-7 Electromagnetic compatibility (EMC) – Part 4-7: Testing and measurement techniques -General guide on harmonics and interharmonics measurements and instrumentation, for power supply systems and equipment connected thereto
IEC 61000-4-8 Electromagnetic compatibility (EMC) – Part 4-8: Testing and measurement techniques -Power frequency magnetic field immunity test
IEC 61000-4-9 Electromagnetic compatibility (EMC) – Part 4-9: Testing and measurement techniques -Impulse magnetic field immunity test
IEC 61000-4-10 Electromagnetic compatibility (EMC) – Part 4-10: Testing and measurement techniques -Damped oscillatory magnetic field immunity test
IEC 61000-4-11 Electromagnetic compatibility (EMC) – Part 4-11: Testing and measurement techniques -Voltage dips, short interruptions and voltage variations immunity tests
IEC 61000-4-12 Electromagnetic compatibility (EMC) – Part 4-12: Testing and measurement techniques -Ring wave immunity test
IEC 61000-6-1 Electromagnetic compatibility (EMC) – Part 6-1: Generic standards – Immunity standard for residential, commercial and light-industrial environments
IEC 61000-6-2 Electromagnetic compatibility (EMC) – Part 6-2: Generic standards – Immunity standard for industrial environments
IEC 61000-6-3 Electromagnetic compatibility (EMC) – Part 6-3: Generic standards – Emission standard for residential, commercial and light-industrial environments
IEC 61000-6-4 Electromagnetic compatibility (EMC) – Part 6-4: Generic standards – Emission standard for industrial environments
IEC 61000-6-5 Electromagnetic compatibility (EMC) – Part 6-5: Generic standards – Immunity for power station and substation environments
IEC 61000-6-7 Electromagnetic compatibility (EMC) – Part 6-7: Generic standards – Immunity requirements for equipment intended to perform functions in a safety-related system (functional safety) in industrial locations
IEC 61326-1 Electrical equipment for measurement, control and laboratory use – EMC requirements –Part 1: General requirements
IEC 61326-2-1 Electrical equipment for measurement, control and laboratory use – EMC requirements – Part 2-1: Particular requirements – Test configurations, operational conditions and performance criteria for sensitive test and measurement equipment for EMC unprotected applications
IEC 61326-2-2 Electrical equipment for measurement, control and laboratory use – EMC requirements – Part 2-2: Particular requirements – Test configurations, operational conditions and performance criteria for portable test, measuring and monitoring equipment used in low voltage distribution systems
IEC 61326-2-3 Electrical equipment for measurement, control and laboratory use – EMC requirements – Part 2-3: Particular requirements – Test configuration, operational conditions and performance criteria for transducers with integrated or remote signal conditioning
IEC 61326-2-4 Electrical equipment for measurement, control and laboratory use – EMC requirements – Part 2-4: Particular requirements – Test configurations, operational conditions and performance criteria for insulation monitoring devices according to IEC 61557-8 and for equipment for insulation fault location according to IEC 61557-9
IEC 61326-2-5 Electrical equipment for measurement, control and laboratory use – EMC requirements – Part 2-5: Particular requirements – Test configurations, operational conditions and performance criteria for field devices with field bus interfaces according to IEC 61784-1
IEC 61326-2-6 Electrical equipment for measurement, control and laboratory use – EMC requirements -Part 2-6: Particular requirements – In vitro diagnostic (IVD) medical equipment
IEC 61326-3-1 Electrical equipment for measurement, control and laboratory use – EMC requirements -Part 3-1: Immunity requirements for safety-related systems and for equipment intended to perform safety-related functions (functional safety) – General industrial applications
IEC 61326-3-2 Electrical equipment for measurement, control and laboratory use – EMC requirements -Part 3-2: Immunity requirements for safety-related systems and for equipment intended to perform safety-related functions (functional safety) – Industrial applications with specified electromagnetic environment
IEC 61340-3-1 Electrostatics – Part 3-1: Methods for simulation of electrostatic effects – Human body model (HBM) electrostatic discharge test waveforms

CISPR (https://webstore.iec.ch)

Document Number Title
CISPR 11

EN 55011

Industrial, scientific and medical (ISM) radio-frequency equipment – Electromagnetic disturbance characteristics – Limits and methods of measurement
CISPR 12 Vehicles, boats and internal combustion engines – Radio disturbance characteristics -Limits and methods of measurement for the protection of off-board receivers
CISPR 13 Sound and television broadcast receivers and associated equipment – Radio disturbance characteristics – Limits and methods of measurement
CISPR 14-1 Electromagnetic compatibility – Requirements for household appliances, electric tools and similar apparatus – Part 1: Emission
CISPR 14-2 Electromagnetic compatibility – Requirements for household appliances, electric tools and similar apparatus – Part 2: Immunity – Product family standard
CISPR 15 Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment
CISPR 16-1-1 Specification for radio disturbance and immunity measuring apparatus and methods -Part 1-1: Radio disturbance and immunity measuring apparatus – Measuring apparatus
CISPR 16-1-2 Specification for radio disturbance and immunity measuring apparatus and methods – Part 1-2: Radio disturbance and immunity measuring apparatus – Coupling devices for conducted disturbance measurements
CISPR 16-1-3 Specification for radio disturbance and immunity measuring apparatus and methods -Part 1-3: Radio disturbance and immunity measuring apparatus – Ancillary equipment -Disturbance power
CISPR 16-1-4 Specification for radio disturbance and immunity measuring apparatus and methods -Part 1-4: Radio disturbance and immunity measuring apparatus – Antennas and test sites for radiated disturbance measurements
CISPR 16-1-5 Specification for radio disturbance and immunity measuring apparatus and methods -Part 1-5: Radio disturbance and immunity measuring apparatus – Antenna calibration sites and reference test sites for 5 MHz to 18 GHz
CISPR 16-1-6 Specification for radio disturbance and immunity measuring apparatus and methods – Part 1-6: Radio disturbance and immunity measuring apparatus – EMC antenna calibration
CISPR 16-2-1 Specification for radio disturbance and immunity measuring apparatus and methods – Part 2-1: Methods of measurement of disturbances and immunity – Conducted disturbance measurements
CISPR 16-2-2 Specification for radio disturbance and immunity measuring apparatus and methods – Part 2-2: Methods of measurement of disturbances and immunity – Measurement of disturbance power
CISPR 16-2-3 Specification for radio disturbance and immunity measuring apparatus and methods -Part 2-3: Methods of measurement of disturbances and immunity – Radiated disturbance measurements
CISPR 16-2-4 Specification for radio disturbance and immunity measuring apparatus and methods – Part 2-4: Methods of measurement of disturbances and immunity – Immunity measurements
CISPR TR 16-2-5 Specification for radio disturbance and immunity measuring apparatus and methods -Part 2-5: In situ measurements for disturbing emissions produced by physically large equipment
CISPR TR 16-3 Specification for radio disturbance and immunity measuring apparatus and methods -Part 3: CISPR technical reports
CISPR TR 16-4-1 Specification for radio disturbance and immunity measuring apparatus and methods – Part 4-1: Uncertainties, statistics and limit modelling – Uncertainties in standardized EMC tests
CISPR 16-4-2 Specification for radio disturbance and immunity measuring apparatus and methods – Part 4-2: Uncertainties, statistics and limit modelling – Measurement instrumentation uncertainty
CISPR TR 16-4-3 Specification for radio disturbance and immunity measuring apparatus and methods -Part 4-3: Uncertainties, statistics and limit modelling – Statistical considerations in the determination of EMC compliance of mass-produced products
CISPR TR 16-4-4 Specification for radio disturbance and immunity measuring apparatus and methods – Part 4-4: Uncertainties, statistics and limit modelling – Statistics of complaints and a model for the calculation of limits for the protection of radio services
CISPR TR 16-4-5 Specification for radio disturbance and immunity measuring apparatus and methods – Part 4-5: Uncertainties, statistics and limit modelling – Conditions for the use of alternative test methods
CISPR 17 Methods of measurement of the suppression characteristics of passive EMC filtering devices
CISPR TR 18-1 Radio interference characteristics of overhead power lines and high-voltage equipment – Part 1: Description of phenomena
CISPR TR 18-2 Radio interference characteristics of overhead power lines and high-voltage equipment -Part 2: Methods of measurement and procedure for determining limits
CISPR TR 18-3 Radio interference characteristics of overhead power lines and high-voltage equipment -Part 3: Code of practice for minimizing the generation of radio noise
CISPR 20 Sound and television broadcast receivers and associated equipment – Immunity characteristics – Limits and methods of measurement
CISPR 22 Information technology equipment – Radio disturbance characteristics – Limits and methods of measurement (Withdrawn and replaced by CISPR 32:2015)
CISPR 24 Information technology equipment – Immunity characteristics – Limits and methods of measurement
CISPR 25 Vehicles, boats and internal combustion engines – Radio disturbance characteristics – Limits and methods of measurement for the protection of on-board receivers
CISPR 32 Electromagnetic compatibility of multimedia equipment – Emission requirements
CISPR 35 Electromagnetic compatibility of multimedia equipment – Immunity requirements

 

2. Wymagania samochodowe, automotive

AUTOMOTIVE ELECTROMAGNETIC COMPATIBILITY STANDARDS (http://www.cvel.clemson.edu/auto/auto_emc_standards.html).

CISPR (AUTOMOTIVE EMISSIONS REQUIREMENTS) (https://webstore.iec.ch)

Document Number Title
CISPR 12 Vehicles, boats, and internal combustion engine driven devices – Radio disturbance characteristics – Limits and methods of measurement for the protection of receivers except those installed in the vehicle/boat/device itself or in adjacent vehicles/boats/devices
CISPR 25 Radio disturbance characteristics for the protection of receivers used on board vehicles, boats, and on devices – Limits and methods of measurement

 

ISO (AUTOMOTIVE IMMUNITY REQUIREMENTS) (https://www.iso.org)

Document Number Title
ISO 7637-1 Road vehicles — Electrical disturbances from conduction and coupling — Part 1: Definitions and general considerations
ISO 7637-2 Road vehicles — Electrical disturbances from conduction and coupling — Part 2: Electrical
transient conduction along supply lines only
ISO 7637-3 Road vehicles — Electrical disturbance by conduction and coupling — Part 3: Vehicles with nominal 12 V or 24 V supply voltage — Electrical transient transmission by capacitive and inductive coupling via lines other than supply lines
ISO/TR 10305-1 Road vehicles — Calibration of electromagnetic feld strength measuring devices – Part 1: Devices for measurement of electromagnetic felds at frequencies > 0 Hz
ISO/TR 10305-2 Road vehicles — Calibration of electromagnetic feld strength measuring devices – Part 2: IEEE standard for calibration of electromagnetic feld sensors and probes, excluding antennas, from 9 kHz to 40 GHz
ISO 10605 Road vehicles — Test methods for electrical disturbances from electrostatic discharge
ISO/TS 21609 Road vehicles — (EMC) guidelines for installation of aftermarket radio frequency transmitting equipment
ISO 11451-1 Road vehicles — Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 1: General principles and terminology
ISO 11451-2 Road vehicles — Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 2: Off-vehicle radiation sources
ISO 11451-3 Road vehicles — Electrical disturbances by narrowband radiated electromagnetic energy — Vehicle test methods — Part 3: On-board transmitter simulation
ISO 11451-4 Road vehicles — Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 4: Bulk current injection (BCI)
ISO 11452-4 Road vehicles — Component test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 4: Bulk current injection (BCI)
ISO 11452-7 Road vehicles — Component test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 7: Direct radio frequency (RF) power injection
ISO 11452-8 Road vehicles — Component test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 8: Immunity to magnetic felds
ISO 11452-10 Road vehicles — Component test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 10: Immunity to conducted disturbances in the extended audio frequency range

 

SAE (AUTOMOTIVE EMISSIONS AND IMMUNITY) (http://standards.sae.org)

Document Number Title
J1113/1 Electromagnetic Compatibility Measurement Procedures and Limits for Components of Vehicles, Boats (Up to 15 M), and Machines (Except Aircraft) (50 Hz to 18 Ghz)
J1113/2 Electromagnetic Compatibility Measurement Procedures and Limits for Vehicle Components (Except Aircraft)–Conducted Immunity, 15 Hz to 250 kHz–All Leads
J1113/4 Immunity to Radiated Electromagnetic Fields-Bulk Current Injection (BCI) Method
J1113/11 Immunity to Conducted Transients on Power Leads
J1113/12 Electrical Interference by Conduction and Coupling – Capacitive and Inductive Coupling via Lines Other than Supply Lines
J1113/13 Electromagnetic Compatibility Measurement Procedure for Vehicle Components – Part 13: Immunity to Electrostatic Discharge
J1113/21 Electromagnetic Compatibility Measurement Procedure for Vehicle Components – Part 21: Immunity to Electromagnetic Fields, 30 MHz to 18 GHz, Absorber-Lined Chamber
J1113/26 Electromagnetic Compatibility Measurement Procedure for Vehicle Components -Immunity to AC Power Line Electric Fields
J1113/27 Electromagnetic Compatibility Measurements Procedure for Vehicle Components – Part27: Immunity to Radiated Electromagnetic Fields – Mode Stir Reverberation Method
J1113/28 Electromagnetic Compatibility Measurements Procedure for Vehicle Components–Part28–Immunity to Radiated Electromagnetic Fields–Reverberation Method (Mode Tuning)
J1752/1 Electromagnetic Compatibility Measurement Procedures for Integrated Circuits Integrated Circuit EMC Measurement Procedures-General and Definition
J1752/2 Measurement of Radiated Emissions from Integrated Circuits — Surface Scan Method (Loop Probe Method) 10 MHz to 3 GHz
J1752/3 Measurement of Radiated Emissions from Integrated Circuits — TEM/Wideband TEM (GTEM) Cell Method; TEM Cell (150 kHz to 1 GHz), Wideband TEM Cell (150 kHz to 8 GHz)
J551/5 Performance Levels and Methods of Measurement of Magnetic and Electric Field Strength from Electric Vehicles, Broadband, 9 kHz To 30 MHz
J551/15 Vehicle Electromagnetic Immunity–Electrostatic Discharge (ESD)
J551/16 Electromagnetic Immunity – Off-Vehicle Source (Reverberation Chamber Method) – Part 16 – Immunity to Radiated Electromagnetic Fields
J551/17 Vehicle Electromagnetic Immunity — Power Line Magnetic Fields
J1812 Function Performance Status Classification for EMC Immunity Testing
J2628 Characterization- Conducted Immunity
J2556 Radiated Emissions (RE) Narrowband Data Analysis–Power Spectral Density (PSD)

 

GM (https://global.ihs.com)

Document Number Title
GMW3091 General Specifcation for Vehicles, Electromagnetic Compatibility (EMC)-Engl; Revision H; Supersedes GMI 12559 R and GMI 12559 V
GMW3097 General Specification for Electrical/Electronic Components and Subsystems, Electromagnetic Compatibility-Engl; Revision H; Supersedes GMW12559, GMW3100,
GMW12002R AND GMW12002V
GMW3103 General Specification for Electrical/Electronic Components and Subsystems, Electromagnetic Compatibility Global EMC Component/Subsystem Validation Acceptance Process-Engl; Revision F; Contains Color; Replaces GMW12003, GMW12004 and GMW3106

FORD (https://www.fordemc.com)

Document Number Title
EMC-CS-2009.1 Component EMC Specification EMC-CS-2009.1
FORD F-2 Electrical and Electronics System Engineering
FORD WSF-M22P5-A1 Printed Circuit Boards, PTF, Double Sided, Flexible

DaimlerChrysler

Document Number Title
DC-10614 EMC Performance Requirements – Components
DC-10615 Electrical System Performance Requirements for Electrical and Electronic Components
DC-11224 EMC Performance Requirements — Components
DC-11225 EMC Supplemental Information and Alternative Component Requirements
DC-11223 EMC Performance Requirements — Vehicle

Automotive Electromagnetic Compatibility Standards From <http://www.cvel.clemson.edu/auto/auto_emc_standards.html>

3. Wymagania medyczne

MEDICAL STANDARDS (https://www.webstore.iec.ch)

Document Number Title
IEC 60601-4-2 Medical electrical equipment – Part 4-2: Guidance and interpretation – Electromagnetic immunity: performance of medical electrical equipment and medical electrical systems
IEC 60601-1-1 Safety requirements for medical electrical systems
IEC 60601-1-2 Medical electrical equipment – Part 1-2: General requirements for basic safety and essential performance – Collateral Standard: Electromagnetic disturbances – Requirements and tests
IEC 60601-2-2 Medical electrical equipment – Part 2-2: Particular requirements for the basic safety and essential performance of high frequency surgical equipment and high frequency surgical accessories
IEC 60601-1-3 Radiation protection in diagnostic x-ray equipment
IEC 60601-1-6 General requirements for basic safety and essential performance – Usability
IEC 60601-1-8 General requirements for basic safety and essential performance – Alarm systems
IEC 60601-1-9 Requirements for environmentally conscious design
IEC 60601-1-10 Requirements for the development of physiologic closed-loop controllers
IEC 60601-1-11 Medical electrical equipment and medical electrical systems used in the home healthcare environment
IEC 60601-1-12 Medical electrical equipment and medical electrical systems used in the medical services environment

 

OTHER RELEVANT STANDARDS (https://www.webstore.iec.ch)

Document Number Title
CISPR 11 Emission requirements for ISM equipment
IEC 60601-1 General requirements for basic safety and essential performance
IEC TR 60601-4-2 Electromagnetic immunity performance
IEC TR 60601-4-3 Considerations of unaddressed safety aspects in the third edition of IEC 60601-1
IEC TR 62354 General testing procedures for medical electrical equipment
ISO 14708-1 Active implantable medical devices

4. Popularne wymagania bezprzewodowe, radiowe

COMMON WIRELESS STANDARDS ETSI STANDARDS (https://www.etsi.org)

 

4. Wymagania Wojskowe – militarne, obronne

COMMON MILITARY RELATED DOCUMENTS AND STANDARDS

Document Number Title
MIL-HDBK-235-1 Military Operational Electromagnetic Environment Profles Part 1C General Guidance, 1 Oct 2010
MIL-HDBK-1857 Grounding, Bonding and Shielding Design Practices, 27 Mar 1998
MIL-STD-220C Test Method Standard Method of Insertion Loss Measurement, 14 May 2009
MIL-STD-449D Radio Frequency Spectrum Characteristics, Measurement of, 22 Feb 1973
MIL-STD-461F Requirements for the Control of Electromagnetic Interference Characteristics of Subsystems and Equipment, 10 Dec 2007
MIL-STD-461G Requirements for the Control of Electromagnetic Interference Characteristics of Subsystems and Equipment, 11 Dec 2015
MIL-STD-464C Electromagnetic Environmental Effects Requirements for Systems, 01 Dec 2010
MIL-STD-1541A Electromagnetic Compatibility Requirements for Space Systems, 30 Dec 1987
MIL-STD-1542B Electromagnetic Compatibility and Grounding Requirements for Space System Facilities, 15 Nov 1991
MIL-STD-1605A Procedures for Conducting a Shipboard Electromagnetic Interference (EMI) Survey (Surface Ships), 08 Oct 2009
DoDI 3222.03 DoD Electromagnetic Environmental Effects (E3) Program, 24 Aug 2014

Polskie standardy wojskowe

NO-06-A200 „Kompatybilność elektromagnetyczna. Poziomy dopuszczalne emisji ubocznych i odporności na narażenia elektromagnetyczne”.
NO-06-A500 „Kompatybilność elektromagnetyczna. Procedury badań zaburzeń elektromagnetycznych i odporności na narażenia elektromagnetyczne”.
NO-06-A201 Kompatybilność elektromagnetyczna –Tłumienność obiektów ekranujących –Wymagania
NO-06-A203

 

5. Wymagania lotnicze, awionika, samolotowe

AEROSPACE STANDARDS AIAA STANDARDS http://www.aiaa.org/default.aspx

Document Number Title
S-121-2009 Electromagnetic Compatibility Requirements for Space Equipment and Systems

RTCA STANDARDS
https://www.rtca.org/

Document Number Title
DO-160G Environmental Conditions and Test Procedures for Airborne Equipment
DO-160G Change 1 Environmental Conditions and Test Procedures for Airborne Equipment
DO-233 Portable Electronic Devices Carried on Board Aircraft
DO-235B Assessment of Radio Frequency Interference Relevant to the GNSS L1 Frequency Band
DO-292 Assessment of Radio Frequency Interference Relevant to the GNSS L5/E5A Frequency Band
DO-294C Guidance on Allowing Transmitting Portable Electronic Devices (T-PEDs) on Aircraft
DO-307 Aircraft Design and Certifcation for Portable Electronic Device (PED) Tolerance
DO-357 User Guide: Supplement to DO-160G
DO-363 Guidance for the Development of Portable Electronic Devices (PED) Tolerance for Civil Aircraft
DO-364 Minimum Aviation System Performance Standards (MASPS) for Aeronautical Information/Meteorological Data Link Services
DO-363 Guidance for the Development of Portable Electronic Devices (PED) Tolerance for Civil Aircraft
DO-307A Aircraft Design and Certification for Portable Electronic Device (PED) Tolerance

SAE STANDARDS www.sae.org/

Document Number Title
ARP 5583A Guide to Certification of Aircraft in a High Intensity Radiation (HIRF) Environment

6. Popularne wymagania bezprzewodowe, radiowe

COMMON WIRELESS STANDARDS ETSI STANDARDS (https://www.etsi.org)

Document Number Title
ETSI EN 300 220 Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Radio equipment to be used in the 25MHz to 1000MHz frequency range with power levels ranging up to 500mW
ETSI EN 300 328 Electromagnetic compatibility and Radio Spectrum Matters (ERM); Wideband transmission systems; Data transmission equipment operating in the 2.4 GHz ISM band and using wide band modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive
ETSI EN 300 330 Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Radio equipment to be used in the 9kHz to 25MHz frequency range and inductive loop systems in the 9kHz to 30MHz frequency range
ETSI EN 300 440 Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Radio equipment to be used in the 1GHz to 40GHz frequency range
ETSI EN 301 489-3 Electromagnetic compatibility and Radio spectrum Matters (ERM); Electromagnetic Compatibility (EMC) standard for radio equipment and services; Part 3: Specific conditions for Short Range Devices (SRD) operating on frequencies between 9kHz and 40GHz
ETSI EN 301 489-17 Electromagnetic compatibility and Radio spectrum Matters (ERM); Electromagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for Wideband data and HIPERLAN equipment
ETSI EN 301 893 Broadband Radio Access Networks (BRAN); 5 GHz high performance RLAN; Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive
ETSI EN 303 413 GPS receivers
ETSI EN 303 417 Wireless Power Transfer

 

Źródła: